MORI SEIKI MODEL NT-1000/WZ – 2009

SKU: MORI-SEIKI-MODEL-NT-1000/WZ ,

2009 MORI SEIKI MODEL NT-1000/WZ 7-AXIS MILL/TURN CENTER

SPECIFICATIONS
CAPACITIES
MAXIMUM WORKPIECE SWING:    14.57”
SWING OVER CROSS SLIDE:    14.57”
SWING OVER CROSS SLIDE (TURRET 2):    11.81”
MAX TURNING DIAMETER (TOOL-SPINDLE):        14.57”
MAX TURNING DIAMETER (TOOL-SPINDLE/TURRET 2):    10.63”
MAX TURNING LENGTH:        16.69”
BAR WORK CAPACITY:        2.05”

TRAVELS
X1-AXIS (TOOL-SPINDLE):    14.96”
Y-AXIS (TOOL-SPINDLE):    + 4.13”
Z1-AXIS (TOOL-SPINDLE):    18.11” + 6.10” (ATC TRAVEL)
B-AXIS (TOOL-SPINDLE):    + 120 DEGREES
X2-AXIS (TURRET 2):    6.10”
Z2-AXIS (TURRET 2):    24.01”
C-AXIS:    .001 DEGREES

SPINDLE
SPEED:    6,000 RPM
NUMBER OF SPINDLE SPEED RANGE (STEP):    2 <WOUND ROTOR>
SPINDLE NOSE TYPE:    JIS A2-5
THROUGH-SPINDLE HOLE DIAMETER:    2.4”
MINIMUM SPINDLE INDEXING ANGLE:    0.0001 DEGREES
SPINDLE BEARING INSIDE DIAMETER:    3.94”

TOOL-SPINDLE (TURRET ONE)
NUMBER OF TOOLS ON HEAD:    1
MINIMUM B-AXIS INDEXING ANGLE:    0.0001 DEGREES
TOOL SPINDLE SPEED:    20,000 RPM
SPINDLE SPEED (STEP ONE):    1,800 – 5,000 RPM
SPINDLE SPEED (STEP TWO):    5,000 – 18,000 RPM
SPINDLE SPEED (STEP ONE):    18,000 – 20,000 RPM
TAPER HOLE OF TOOL-SPINDLE:    HSK-A50/C6
INSIDE DIAMETER OF TOOL-SPINDLE BEARING:    2.56”
TOOL MAGAZINE:    38 POSITIONS
MAXIMUM TOOL DIAMETER:    2.76”
MAXIMUM TOOL DIAMETER (NO ADJACENT TOOLS):    5.12”
MAXIMUM TOOL MASS:    11 LBS

TURRET 2
NUMBER OF TOOLS:    8
SQUARE SHANK HEIGHT OF SINGLE POINT TOOL:    .79” / 20 MM
SHANK DIAMETER OF BORING BAR:    1.26” / 32 MM

MOTORS
SPINDLE DRIVE MOTOR (30 MIN/CONT):    15/10 HP
TOOL-SPINDLE MOTOR (40%/CONT):    7.5/5 HP (1,800 – 18,000 RPM)
TOOL-SPINDLE MOTOR (40%/CONT):    5/3 HP (18,000 – 20,000 RPM)

GENERAL
WEIGHT:    18,700 LBS
ELECTRICS

EQUIPPED WITH
FANUC MSX-711IV MAPPS-III CONTROL
.001 DEGREE FULL CONTOURING (B-AXIS)
HYDRAULICS THRU TURRET I/F
LOWER TURRET EXTENDED TRAVEL OF 200 MM
COOLANT FILTRATION SYSTEM
HINGE BELT CHIP CONVEYOR (RIGHT SIDE)
RENISHAW PROBE SYSTEM
150 PSI THROUGH SPINDLE COOLANT
5 SETS OF M-CODES
PROGRAMMING RESOLUTION BY 1/10
MICROCENTRIC CB65 HYDRAULIC CHUCK
TAILSTOCK FOR TURRET