Okuma Multus U4000-2SC-2000 – 2016

OKUMA MULTUS U4000
SPECIFICATIONS:

POWER 30 hp
MAX RPM 4,200 RPM
TURNING DIA 25.59″
MULTUS U4000 2SC2000 with OSP-P300SA

2SC U4000 MULTUS OKUMA ,

OKUMA Intelligent Multitasking Model MULTUS U4000 2SC2000 with OSP-P300SA CNC Controller (19 inch OSP suite) including CE mark

European Standard Specification
Main spindle PREX motor 22/15kW (30 min./cont.) Main Spindle speed, 45 – 4,200 min-1
Main Spindle JIS A2-8, bore dia. 91mm No chuck & no tube for Main-Spindle
Hollow cylinder SR1670 for main spindle, not incl. draw tube Chuck auto open / close with confirmation for main and sub C-axis control, 360 degree at 0.001 degree increment
Y-axis stroke 300mm (+150mm – -150mm) H1 ATC turret HSK-A63
40-tool ATC
Rotary tool drive motor, VAC 22/15/11 KW (3 min./15 min./cont.) Rotary tool spindle speed, 12,000 min-1
NC Tailstock, dead Center Type MT No.5 (*2SC: Hydraulic quill type) “Tailstock travelling stroke, 1594 / 2094mm (*BCD1500 / 2000) for 1SC model
Tailstock travelling stroke, 1359.5 / 1961mm (*BCD1500 / 2000) for 2SC model”
Tailstock quill sizing confirmation (with acrylic cover for confirm L/S) Revolving center, MT No.5 (Non carbide tipped)
Hydraulic power unit
M spindle through coolant 2.0Mpa, 20L/min Pump for Chip flusher and External M-spindle coolant:0.8kW+Pumping pump:0.25kW Totally enclosed chip and coolant shield
Door interlock
Work light, LED, left and right each Foundation washers and leveling jack screws Machine lifting hooks & hand tools
Lower turret V12 (*2SC: Turret for directly mounted tools / 2SW: Radial type)
M spindle through coolant supply spec. B-axis indexing, 0.001 degree indexing
Lubrication monitor A-1+ Hydraulic original Chip pan
Application for IEC standard Touch setter M
Double type chuck operation pedal CE mark and EMC
Dummy holder HSK-A63 Machine raise up 75mm (*2S)
OSP-P300SA 3D-M-E kit specifications
*Workpiece coordinate system selection 10 sets
*Coordinate conversion

*Profile generation
*Coordinate computation (including NYCL command)
*Coordinate change: shift, rotate, copy
*Real 3D simulation
*Cycle time over check
*Load monitor (spindle, feed axis)
*NC operation monitor (incl. counter and totalization function)
*Signal tower 1 colours
*Spindle speed modulation control
*Cycle time reduction function
*Hi-Cut Pro
Colour 19″ screen and tilting operation panel Thermo-Friendly Concept (H1 TAS-S and TAS-C) Collision Avoidance System
Tool compensation * Implemented as “Easy-to-operate functions” Pitch error compensation X/Y/Z axis (*2S: +Xb, Zb axis) Workpiece jump out detection
Electrical Power Source Application to suite local power source at each countries
No test trial in JAPAN

Remarks:
1) No standard tool holder is included.
Note When a machine is used with automation system like a loader and a robot etc., please invariably select “Ceiling shower coolant A” or “B”. in order to avoid chipping accumulation on a lower turret.
2. OKU-2160110 Main Big bore spindle, A2-11, 3,000min-1, PREX32

Main Big bore spindle, A2-11, 3,000min-1, PREX32/22kW incl. F2596 (only cylinder), incl. pre-arr. Hydraulic temperature regulator
3. OKU-2160630 Built-in center type tailstock, MT No.4, incl.

Built-in center type tailstock, MT No.4, incl. 1pc of tailstock center i/o tailstock center MT No.5
4. OKU-2160810 Front door auto open / close, with safety rubber

Front door auto open / close, with safety rubber switch for CE mark, 2 connected doors opening type (x2000)
5. OKU-2160845 Rotary wiper, electrical type (x2000) on 1-windo

Rotary wiper, electrical type (x2000) on 1-window (on left door)
6. OKU-2160910 Hinge chip conveyor H-type, Side chip disposal [
Hinge chip conveyor H-type, Side chip disposal [1S/2S x 2000]
incl. machine linked control and Intermittent feed for conveyor
7. OKU-2160940Chip bucket H

 

8. OKU-2160985 Conveyor torque limiter, alarm C in case detecti

Conveyor torque limiter, alarm C in case detection
9. OKU-2160995 Oil skimmer

10. OKU-2161014 High pressure coolant unit 7MPa i/o STD 2MPa

High pressure coolant unit 7MPa i/o STD 2MPa [2S]
* H1 Through spindle coolant: H/L pressure switchable
* External M-spindle coolant: Low pressure only
* Lower turet coolat: H/L pressure switchable
* Ogura high pressure coolant unit Separate placement type with cyclone filter is included.
[ in case of Hinge type conveyor ]
11. OKU-2161030 Shower coolant B for main spindle side

12. OKU-2161080 Coolant gun

13. OKU-2162001 High precision C-axis for main spindle ( incl. 1

High precision C-axis for main spindle ( incl. 1/10μ
control software and name plate)
14. OKU-2163025 H1 Turret air blower (L-holder / periphery of M-

H1 Turret air blower (L-holder / periphery of M-spindle) with Through air blower during M-spindle rotation (air / coolant switchable type)
15. OKU-9311905 External M-code, 8 sets

16. OKU-2164020 In process gauging, Renishaw RMP60

In process gauging on H1 turret, Renishaw RMP60, Straight type
17. OKU-2165030 Pre-arr. for Mist collector (Dia. 198mm Duct,

Pre-arr. for Mist collector (Dia. 198mm Duct, and cap cover at the Right side cover) *Without electrical power and control
18. OKU-9311417 Y axis gauging function

incl. gauging in slope machining mode
19. —

20. OKU-9311114 Helical cutting function for MacTurn/MULTUS seri

Helical cutting function for MacTurn/MULTUS series (incl. Slope function)

Note: Interpolates circular lines,Corects tool diameter on incline surface. Graphic function.

21. OKU-2161091 Coolant level detection (lower limit)

22. FA-OEG-201605 Coolant flow meter with display on OSP & alarm

Coolant flow meter with display on OSP and alarm (+ Additional Input Signals)
23. OKU-2160710 80ATC (40 x 2-row magazine type) i/o STD 40ATC

24. OKU-2162040 Coolant temperature regulator

25. OKU-9311621 Robot loader interface type E *except Sub-spindl

Robot loader interface type E *except Sub-spindle spec.
* Auto door spec. should be selected separetely
* Chuck air blower should be selected separately.

Note: In case VTM-YB and VTR, this is TBA, because of our no experience .
26. OKU-9311125 Multi tool function (for HSK or Capt)
Note: Multi tool function is for only MACTURN and MULTUS .
Note: VTM-1200YB / 2000YB with HSK-A100 or Capt C8 specs. are also available.
27. OKU-2166235 OD tool holder I-S (V12)

28. OKU-2166265 ID tool holder H40 (V12)

29. OKU-2166270 Oil hole ID tool holder base H40-U (V12)

30. OKU-2166245 OD tool holder II (V12)

31. OKU-2166275 ID tool holder H40 (V12) for high pressure

32. OKU-2166280 Oil hole ID tool holder base H40-U (V12) for

Oil hole ID tool holder base H40-U (V12) for high pressure
33. OKU-2168005 Hobbing cut package, Programing function II /

Hobbing cut package, Programing function II /Hobbing cut function
34. OKU-2164025 Tool breakage detection for upper turret tool